Difference between revisions of "Hardware/MX23L4005"
< Hardware
Jump to navigation
Jump to search
m |
m |
||
| Line 5: | Line 5: | ||
Observed pin behavior: | Observed pin behavior: | ||
1 connected to power button - active high | 1 connected to power button - active high | ||
| − | 2 wii power state (+3.3v when power is on, 0v otherwise) TP113 | + | 2 wii power state (+3.3v when power is on or in standby, 0v otherwise) TP113 comes on slightly after pin 3 |
| − | 3 wii power state (+3.3v when power is on, 0v otherwise) | + | 3 wii power state (+3.3v when power is on or in standby, 0v otherwise) |
4 Gnd | 4 Gnd | ||
| − | 5 0? TP46 | + | 5 0? TP46 pulses occasionally to 1 |
6 1? TP106 | 6 1? TP106 | ||
7 0? TP45 | 7 0? TP45 | ||
| Line 14: | Line 14: | ||
8 0? measuring this pin prevents the wii from shutting off when you hold the power button down ?!!? | 8 0? measuring this pin prevents the wii from shutting off when you hold the power button down ?!!? | ||
9 nc? | 9 nc? | ||
| − | 10 TP109 | + | 10 TP109 0? |
| − | 11 TP43 | + | 11 TP43 0? |
| − | 12 TP44 | + | 12 TP44 exi? |
| − | 13 TP41 | + | 13 TP41 exi? |
| − | 14 TP42 | + | 14 TP42 exi? |
| − | 15 | + | 15 exi? |
16 Gnd | 16 Gnd | ||
| − | 17 | + | 17 3.3v when wii has power applied |
| − | 18 | + | 18 3.3v when wii has power applied |
| − | 19 TP108 | + | 19 TP108 measuring this causes wii to power on immediately |
| − | 20 TP231 | + | 20 TP231 0? |
| − | 21 TP110 | + | 21 TP110 3.3v when wii has power applied, goes low briefly when powering off |
22 xtal | 22 xtal | ||
23 xtal | 23 xtal | ||
| − | 24 TP119 | + | 24 TP119 turns on shortly after poweron |
| − | 25 TP117 | + | 25 TP117 +3.3v when wii has power |
| − | 26 TP116 | + | 26 TP116 0? |
| − | 27 | + | 27 +3.3v when wii has power |
| − | 28 | + | 28 0? |
Revision as of 15:30, 15 December 2008
The custom MX23L4005 chip used on the Nintendo Wii contains the GameCube font set, RTC, and power management functions. It is listed on WiiRe as "U8: MX "E062674-MG" "MX23L4005-24C1" "RTC-RVL A" "2S08802" (RTC, TSOP28 18x8mm)".
Die shot: http://www.bunniestudios.com/blog/?p=227
Observed pin behavior:
1 connected to power button - active high 2 wii power state (+3.3v when power is on or in standby, 0v otherwise) TP113 comes on slightly after pin 3 3 wii power state (+3.3v when power is on or in standby, 0v otherwise) 4 Gnd 5 0? TP46 pulses occasionally to 1 6 1? TP106 7 0? TP45
8 0? measuring this pin prevents the wii from shutting off when you hold the power button down ?!!? 9 nc? 10 TP109 0? 11 TP43 0? 12 TP44 exi? 13 TP41 exi? 14 TP42 exi?
15 exi? 16 Gnd 17 3.3v when wii has power applied 18 3.3v when wii has power applied 19 TP108 measuring this causes wii to power on immediately 20 TP231 0? 21 TP110 3.3v when wii has power applied, goes low briefly when powering off
22 xtal 23 xtal 24 TP119 turns on shortly after poweron 25 TP117 +3.3v when wii has power 26 TP116 0? 27 +3.3v when wii has power 28 0?